Wear Metals Standard

Catalog NumberCat. #
10 µg/g in 75 cSt Base oil
Number of ComponentsComps
200 g

Additional Information

10 µg/g
Storage ConditionStorage
Ambient (>5 °C)
Safety Data SheetSDS
AnalyteCAS NumberElement AbbreviationTarget Concentration
Aluminum7429-90-5Al10 µg/g
Barium7440-39-3Ba10 µg/g
Boron7440-42-8B10 µg/g
Cadmium7440-43-9Cd10 µg/g
Calcium7440-70-2Ca10 µg/g
Chromium7440-47-3Cr10 µg/g
Copper7440-50-8Cu10 µg/g
Iron7439-89-6Fe10 µg/g
Lead7439-92-1Pb10 µg/g
Magnesium7439-95-4Mg10 µg/g
Manganese7439-96-5Mn10 µg/g
Molybdenum7439-98-7Mo10 µg/g
Nickel7440-02-0Ni10 µg/g
Phosphorus7723-14-0P10 µg/g
Silicon7440-21-3Si10 µg/g
Silver7440-22-4Ag10 µg/g
Sodium7440-23-5Na10 µg/g
Tin7440-31-5Sn10 µg/g
Titanium7440-32-6Ti10 µg/g
Vanadium7440-62-2V10 µg/g
Zinc7440-66-6Zn10 µg/g
Molecular Formula Mol. Formula
Molecular Weight Mol. Weight
Melting Point Melting Point
Boiling Point Boiling Point
>600 °F (>315 °C)
Flash Point Flash Point
450°F / 232°C (coc)
Refer to SDS for detailed product information.
HAZ00004 HAZ00006
Signal word
Hazard statements
Aspiration hazard if swallowed - may be harmful if swallowed and enters airways. (Aspiration hazard, catagory 2)
Irritating to skin. (Skin corrosion/irritation, category 2)
May be irritating to mucous membrane and upper respiratory system. (Specific target organ toxicity, single exposure; Respiratory tract irritation, category 3)
Precautionary statements

Eye contact: Immediately flush with plenty of water. After initial flushing, remove and contact lenses and continue flushing for at least 15 minutes. Assure adequate flushing by separating the eyelids with fingers. (P338)
Skin contact: Immediately wash skin with soap and plenty of water. Remove contaminated clothing. Get medical attention if symptoms occur. Wash clothing before reuse. (P360)
Ingestion: Do NOT induce vomiting. Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person. (P331)
Evacuate the area of all non-essential personnel. Wear a self-contained breathing apparatus and appropriate personal protection. Eliminate any ignition sources until the area is determined to be free from explosion or fire hazards. Contain the release and eliminate its source, if this can be done without risk. Take up and containerize for proper disposal. Comply with Federal, State, and local regulations. (P380)
Store in a tightly closed container. (P404)
Do not get in eyes, on skin or clothing. (P262)
This product should only by used by persons trained in the safe handling of hazardous chemicals. (P202)
Wash thoroughly after handling. Do not take internally. Eye wash and safety equipment should be readily available. (P264)
Respiratory Protection: If workplace exposure limit(s) of product or any component is exceeded (see TLV/PEL), or a risk assessment shows air-purifying respirators are appropriate, use of a NIOSH/MSHA approved air supplied respirator is advised. Use a full-face respirator with multi-purpose combination (US) or type ABEK (EN14387) respirator cartridges in absence of proper environmental control. Always use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU). Engineering and/or administrative controls should be implemented to reduce exposure.

UN Number UN #
Shipping Class Shp Class
Packing Group Packing